EPLAN Electric P8 2.6 (Electric P8, Fluid, PPE, Pro Panel) 2.6 x64 [2016, ENG + RUS]

Installation on Win10 x64
1. Install MS Office 2013 or 2016 (64 bit)
2. Install the Net Framework 4.0
3. Disable UAC: Control Panel - User Accounts - Change User Account Control Settings - Slider to the bottom position (Never notify)
4. Install EPLAN on the C:
5. Copy the license file "SN-U10066.EGF" from the EPLAN P8 folder 2.6 patch Windows x32x64 to C: \ Users \ General \ EPLAN \ Common
Copy the version.dll file to: C: \ Program Files \ EPLAN \ Platform \ 2.6.3 \ Bin
5.1 Set the file attributes: read only and system (so that the license does not fly).
6. Remove the driver of the protection key "HL Hasp" via the control panel (Control Panel -> Uninstall the program) if it is installed !!!
7. Install the new haspdinst.exe driver (see readme.html) (HASPUserSetup.exe)
8. Run 10066.reg and add to the registry
9. Copy all files from the EPLAN folder P8 2.6 patch Windows x32x64 \ Release \ MultiKey64
In Windows / System32. Launch the Virtual USB Multikey installation: right-click on Windows / System32 / install.cmd and run as administrator.
If everything is done correctly, the Virtual USB Multikey will appear in the device manager-system devices.
Instead, an unidentified device appears in Device Manager.
10. Turn on the Windows test mode: Run dseo13b.exe and select "Enable Test Mode". Exit the program through EXIT.
11. Reboot. Before starting Windows, press and hold the F8 button. Selecting Disable mandatory driver signature verification
12. Installing Hardlock drivers: Run dseo13b.exe and select "Sign a system file". Enter C: \ Windows \ System32 \ Drivers \ multikey.sys.
Through the Device Manager, we update the driver to an unidentified device, which it will find in the Windows / System32 /
If everything is done correctly, the SafeNetInc.Hardlock key and the SafeNetInc.USB key appear in the device manager - USB controllers.
Exit the program through EXIT.
13. Reboot.
14. Starting the EPLAN.
There is an Internal error when opening projects of older versions. However, if you open the eplan and wait 5 minutes without doing anything, you will see a message: Due to a hardware conflict on your system, you can start Eplan only with a limited power. Error 4521.
Click Close
Then click Open project and voila! Projects of old versions open without problems! Having found this error, I found the following:
Error 4521.
This message appears because EPLAN discovered the use of workstations to circumvent license protection ("hacked", "pirated" licenses).
EPLAN will run on this workstation only for 30 days. (
15. Copy the license file "SN-U10066.EGF" from the EPLAN P8 folder 2.6 patch Windows x32x64 to C: \ Users \ General \ EPLAN \ Common
Copy the version.dll file to: C: \ Program Files \ EPLAN \ Platform \ 2.6.3 \ Bin
15.1 Install (check) file attributes: read only and system (so that the license does not fly).

We treat on Win10 x64
1. Install EPLAN.
2. Run the command prompt with administrator rights and assign 2 commands in turn.
Bcdedit -set loadoptions DISABLE_INTEGRITY_CHECKS
Bcdedit -set TESTSIGNING ON
Reload.
3. Install HASPUserSetup with administrator rights. Reload.
4. Start EPLAN2.1 2.3 2.4 2.5 2.6 X64 crack with administrator rights. Copy version.dll to "From: \ Program Files \ EPLAN \ Platform \ 2.6.3 \ Bin". Reload.
5. Go to the device manager, there will be an undefined driver hang, click the driver update and specify the update path from the Virtual USB Multikey Dongle 64bit driver folder. Reload.
6. Launch EPLAN, select the required license.